Wastewater Recycling - BoomEnviro.com

The WRS 52 Wastewater Recycling System is designed to solve wastewater treatment and disposal problems for the very high volume user. This extra high capacity COMPLETELY AUTOMATIC WASTEWATER TREATMENT UNIT will collect dirty, oily wastewater and recycle it so that it can be reused in the washing operation. The recycle feed pump transfers the dirty water from a collection sump to the wastewater treatment unit. Reagents are automatically added in during the wastewater recycling process to kill bacteria and odors, neutralize the pH, and remove pollutants such as oil, grease, dirt, and sludge. These reagents used in the wastewater recycling process are commonly used in drinking water treatment, and actually make the water much more ENVIRONMENTALLY FRIENDLY and less hazardous for personnel doing the washing. The treated water is then stored until needed for washing.

The WRS 52 treats up to 16 gpm (23000 gpd), which is plenty for even very large wastewater recycling and washing operations. This unit is equipped with many convenience features, including automatic priming valves for the reagent pumps, integral water storage tank, and filters status pressure gage. It comes completely assembled and wired, ready to be set in place and plugged into a 15 amp, 115 volt outlet. The water discharge from the integral storage tank is pressurized to feed your pressure washers, even if they are remotely located. Premium components insure the most troublefree operation possible.

Rated flow rate:	Up to 16 gpm (23000 gpd)
Electrical requirement:	115 VAC, 60 Hz, 1 phase, 15 amp total
Recycle feed pump:	Self priming centrifugal cast iron pump with 1/2 HP thermally protected motor. Mounted on the machine base. Controlled by float switch in collection pit. Suction line strainer and foot valve are provided.
Discharge pump:	High head centrifugal pump with1/2 HP thermally protected motor. Provides pressurized water flow to pressure washer and other uses.
Electrical controls:	GFCI provided, prewired with 15 amp plug, 10 ft cord Lighted switches. pH controller with digital display. NEMA 4 rated enclosure
Reagent metering pumps:	Electronic controlled diaphragm pumps with stroke rate and stroke length controls and automatic degassing head for ease of priming. Three pumps are supplied, for coagulant, oxidizer, and pH adjuster. Pumps are mounted in a fiberglass enclosure.
Inlet strainer:	Large size with stainless steel screen in corrosion resistant plastic housing.
Filter system:	Two 20" long 20 micron filter cartridges for final polishing.
Sludge collection system:	Four large, disposable fabric socks collect sludge.
Make up water:	6 to 16 gpm required. 100 psi maximum pressure.
Recycle tank capacities:	Coagulant tank- 180 gallons Separator tank- 240 gallons Storage tank- 150 gallons Total water capacity- 570 gallons
Recycle construction:	Heavy duty polypropylene tank with unitized construction. Schedule 80 PVC pipe used throughout. Heavy steel base assembly.
Connection sizes:	Machine inlet- 1 1/2 MNPT Treated water outlet- 1 FNPT Drain line- 1 FNPT Make up water- 1/2 FNPT
Overall dimensions:	8 ft 0 in long, 4 ft 2 in deep, 4 ft 3 in tall
Shipping weight:	900 pounds
Options:	Second pH adjusting pump system. Additional treated water storage capacity. Sand filter final polishing system. Activated carbon water polishing systems. Ozone treatment. Pretreatment systems, oil skimmers, and oily water separators. Graduated reagent containers. Custom modifications available.
Rated flow rate:	Up to 12 gpm (18000 gpd)
Electrical requirement:	115 VAC, 60 Hz, 1 phase, 15 amp total
Recycle feed pump:	Self priming centrifugal cast iron pump with 1/2 HP thermally protected motor. Mounted on the machine base. Controlled by float switch in collection pit. Suction line strainer and foot valve are provided.
Discharge pump:	High head centrifugal pump with1/2 HP thermally protected motor. Provides pressurized water flow to pressure washer and other uses.
Electrical controls:	GFCI provided, prewired with 15 amp plug, 10 ft cord Lighted switches for power, feed pump, coagulant pump, oxidizer pump, pH adjuster pump, makeup water, and manual drain. pH controller with digital display. NEMA 4 rated enclosure
Reagent metering pumps:	Electronic controlled diaphragm pumps with stroke rate and stroke length controls and automatic degassing head for ease of priming. Three pumps are supplied, for coagulant, oxidizer, and pH adjuster. Pumps are mounted in a fiberglass enclosure.
Inlet strainer:	Large size with stainless steel screen in corrosion resistant plastic housing.
Filter system:	Two 20" long 20 micron filter cartridges for final polishing. Two sets included.
Sludge collection system:	Three large, disposable fabric socks collect sludge. Two sets included with machine.
Make up water:	100 psi maximum pressure. Automatically added as required by application.
Recycle tank capacities:	Coagulant tank- 150 gallons Separator tank- 180 gallons Storage tank- 150 gallons Total water capacity- 480 gallons
Recycle construction:	Heavy duty polypropylene tank with unitized construction. Schedule 80 PVC pipe used throughout. Heavy steel base assembly.
Connection sizes:	Machine inlet- 1 1/2 MNPT Treated water outlet- 3/4 FNPT Drain line- 1 FNPT Make up water- 1/2 FNPT
Overall dimensions:	8 ft 0 in long, 3 ft 8 in deep, 4 ft 3 in tall
Shipping weight:	900 pounds
Options:	Second pH adjusting pump system. Additional treated water storage capacity. Sand filter final polishing system. Activated carbon water polishing systems.
Rated flow rate:	2 gpm (3000 gpd)
Electrical requirement:	115 VAC, 60 Hz, 1 phase, 15 amp total
Recycle feed pump:	Self priming centrifugal cast iron pump with 1/3 HP thermally protected motor. Mounted on the machine base on WRS 12+. Controlled by float switch in collection pit. Suction line strainer and foot valve are provided.
Discharge pump:	High head centrifugal pump with 1/2 HP thermally protected motor. Provides pressurized water flow to pressure washer and other uses.
Electrical controls:	GFCI provided, prewired with 15 amp plug, 10 ft cord Lighted switches for power, feed pump, coagulant pump, oxidizer pump, pH adjuster pump, makeup water, and manual drain. pH controller with digital display. NEMA 4 rated enclosure
Reagent metering pumps:	Electronic controlled diaphragm pumps with stroke rate and stroke length controls. Automatic degassing head on oxidizer and pH adjust pump. Manual bleed valve on coagulant pump. Pumps are mounted in a fiberglass enclosure on WRS 12+.
Inlet strainer:	Large size in corrosion resistant plastic housing. Valve-in-head housing on WRS 12+.
Filter system:	20" long 20 micron filter cartridge for final polishing. Two cartridges included with machine.
Sludge collection system:	Large, disposable fabric filter sock collects sludge. Two filter socks included with machine.
Make up water:	100 psi maximum pressure. Automatically added as required by application.
Recycle tank capacities:	Coagulant tank- 50 gallons Separator tank- 50 gallons Storage tank- 50 gallons Total water capacity- 150 gallons
Recycle construction:	Heavy duty polypropylene tank with unitized construction. Schedule 80 PVC pipe used throughout. Heavy steel base assembly.
Connection sizes:	Machine inlet- 1 NPT Treated water outlet- 3/4 NPT Drain line- 1 NPT Make up water- 1/2 NPT
Overall dimensions:	5 ft 9 in long, 2 ft 8 in deep, 4 ft 3 in tall
Shipping weight:	400 pounds
Options:	Second pH adjusting pump. Additional treated water storage capacity. Activated carbon water polishing systems. Sand filter final polishing system. Pretreatment systems, oil skimmers, and oily water separators. Ozone treatment. Graduated reagent containers. Custom modifications available. 798